Bronze NSA T1G
Using MAC Tile Adhesive for your wall or flooring offers many advantages – both during the bonding process and following installation. When installing ceramic tile, an tile adhesive is often perfect for the job, and will improve ease of application. we have a broad range of smart technologies for you to choose from. At MAC, we’re committed to ensuring your installations maintain their durability in the long run – whether you’re installing tiles.
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA T1G Grey meets the adhesive requirements of ISI
About Bronze NSA T1G
- Our ceramic Tile Adhesive are compatible with a wide range of substrates:
- Applying ceramic wall tiles on wall internally
- Applying vitrified tiles on floor (600×600 mm, 600×1200 mm, 800×800 mm, 800×1200 mm)
- Applying floor tiles on floor (300x300mm, 400×400 mm).
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA SILVER meets the adhesion requirements of IS 15477 : 2004 “Specification for Adhesives for use with Ceramic Tiles
- Surface Preparation
The surface should be sound, clean, and free from dirt, oil or grease before MAC Bronze NSA T1G is applied. Substrate should be in Saturated Surface Dry (SSD) condition before application of adhesive. Substrates should be in plumb before application of adhesive
- Mixing
Mix 20 kg of MAC Bronze NSA T1G with 5 to 6 liters of water. Mix to a uniform lump-free consistency using a forced action mixer. Keep it for approximately 5 minutes to fatten it. Hand mixing is recommended for small quantities only. Mix as much quantity as can be consumed in 45 min.
- Application
Apply MAC Bronze NSA T1G paste on substrate with plain side of notch trowel. Press paste firmly to work into substrate.Comb with notch trowel with notched side, notch trowel to be selected as per required bed thickness. Spread as much adhesive paste as can be tiled within 15 minutes. Start placing/fixing of tiles & tap using beating block or rubber mallet. For large format tiles & stone provide back butter for 100 % coverage & firm bonding. Periodically remove a tile to check transfer of material on tile. Also check spread of adhesive, if not proper and if becomes non-sticky then scrap it & apply paste again.
- Grouting
Grouting should preferably be carried out at least 24 hours after the completion of tiling. For grout joints upto 3mm wide use Proofer High Polymer Tile Grout. For grout joints above 3mm wide use RTM Wide. After grouting clean and polish tiles with a damp sponge or cloth.
- Cleaning
Clean the tools & equipments with potable water immediately after use.
- Always add powder to liquid and not liquid to powder.
- While working in temperature more than 35OC ( 95OF ) always dampen the substrate & finish faster.
- Tiling should not be done when surface temperature is below 4OC.
Silver NSA T2G
Using MAC Tile Adhesive for your wall or flooring offers many advantages – both during the bonding process and following installation. When installing ceramic tile, an tile adhesive is often perfect for the job, and will improve ease of application. we have a broad range of smart technologies for you to choose from. At MAC, we’re committed to ensuring your installations maintain their durability in the long run – whether you’re installing tiles.
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA T2G Grey meets the adhesive requirements of ISI
About silver NSA T2G
- Our ceramic Tile Adhesive are compatible with a wide range of substrates:
- Applying ceramic wall tiles on wall internally
- Applying vitrified tiles on floor (600×600 mm, 600×1200 mm, 800×800 mm, 800×1200 mm)
- Applying floor tiles on floor (300x300mm, 400×400 mm).
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA SILVER meets the adhesion requirements of IS 15477 : 2004 “Specification for Adhesives for use with Ceramic Tiles
- Surface Preparation
The surface should be sound, clean, and free from dirt, oil or grease before MAC Bronze NSA T2G is applied. Substrate should be in Saturated Surface Dry (SSD) condition before application of adhesive. Substrates should be in plumb before application of adhesive
- Mixing
Mix 20 kg of MAC Bronze NSA T2G with 5 to 6 liters of water. Mix to a uniform lump-free consistency using a forced action mixer. Keep it for approximately 5 minutes to fatten it. Hand mixing is recommended for small quantities only. Mix as much quantity as can be consumed in 45 min.
- Application
Apply MAC Bronze NSA T2G paste on substrate with plain side of notch trowel. Press paste firmly to work into substrate.Comb with notch trowel with notched side, notch trowel to be selected as per required bed thickness. Spread as much adhesive paste as can be tiled within 15 minutes. Start placing/fixing of tiles & tap using beating block or rubber mallet. For large format tiles & stone provide back butter for 100 % coverage & firm bonding. Periodically remove a tile to check transfer of material on tile. Also check spread of adhesive, if not proper and if becomes non-sticky then scrap it & apply paste again.
- Grouting
Grouting should preferably be carried out at least 24 hours after the completion of tiling. For grout joints upto 3mm wide use Proofer High Polymer Tile Grout. For grout joints above 3mm wide use RTM Wide. After grouting clean and polish tiles with a damp sponge or cloth.
- Cleaning
Clean the tools & equipments with potable water immediately after use.
- Always add powder to liquid and not liquid to powder.
- While working in temperature more than 35OC ( 95OF ) always dampen the substrate & finish faster.
- Tiling should not be done when surface temperature is below 4OC.
Gold NSA T3G / T3W
Using MAC Tile Adhesive for your wall or flooring offers many advantages – both during the bonding process and following installation. When installing ceramic tile, an tile adhesive is often perfect for the job, and will improve ease of application. we have a broad range of smart technologies for you to choose from. At MAC, we’re committed to ensuring your installations maintain their durability in the long run – whether you’re installing tiles.
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA T3G Grey meets the adhesive requirements of ISI
About Gold NSA T3G
- Our ceramic Tile Adhesive are compatible with a wide range of substrates:
- Applying ceramic wall tiles on wall internally
- Applying vitrified tiles on floor (600×600 mm, 600×1200 mm, 800×800 mm, 800×1200 mm)
- Applying floor tiles on floor (300x300mm, 400×400 mm).
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA T3G/W GOLD meets the adhesion requirements of IS 15477 : 2004 “Specification for Adhesives for use with Ceramic Tiles
- Surface Preparation
The surface should be sound, clean, and free from dirt, oil or grease before MAC Gold NSA T3G/W is applied. Substrate should be in Saturated Surface Dry (SSD) condition before application of adhesive. Substrates should be in plumb before application of adhesive
- Mixing
Mix 20 kg of MAC Gold NSA T3G/W with 5 to 6 liters of water. Mix to a uniform lump-free consistency using a forced action mixer. Keep it for approximately 5 minutes to fatten it. Hand mixing is recommended for small quantities only. Mix as much quantity as can be consumed in 45 min.
- Application
Apply MAC Gold NSA T3G/W paste on substrate with plain side of notch trowel. Press paste firmly to work into substrate. Comb with notch trowel with notched side, notch trowel to be selected as per required bed thickness. Spread as much adhesive paste as can be tiled within 15 minutes. Start placing/fixing of tiles & tap using beating block or rubber mallet. For large format tiles & stone provide back butter for 100 % coverage & firm bonding. Periodically remove a tile to check transfer of material on tile. Also check spread of adhesive, if not proper and if becomes non-sticky then scrap it & apply paste again.
- Grouting
Grouting should preferably be carried out at least 24 hours after the completion of tiling. For grout joints upto 3mm wide use Proofer High Polymer Tile Grout. For grout joints above 3mm wide use RTM Wide. After grouting clean and polish tiles with a damp sponge or cloth.
- Cleaning
Clean the tools & equipments with potable water immediately after use.
- Always add powder to liquid and not liquid to powder.
- While working in temperature more than 35OC ( 95OF ) always dampen the substrate & finish faster.
- Tiling should not be done when surface temperature is below 4OC.
Platinum NSA T4G/T4W
Using MAC Tile Adhesive for your wall or flooring offers many advantages – both during the bonding process and following installation. When installing ceramic tile, an tile adhesive is often perfect for the job, and will improve ease of application. we have a broad range of smart technologies for you to choose from. At MAC, we’re committed to ensuring your installations maintain their durability in the long run – whether you’re installing tiles.
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA T4G/T4W meets the adhesive requirements of ISI
About Platinum NSA T4G/T4W
- Our ceramic Tile Adhesive are compatible with a wide range of substrates:
- Applying ceramic wall tiles on wall internally
- Applying vitrified tiles on floor (600×600 mm, 600×1200 mm, 800×800 mm, 800×1200 mm)
- Applying floor tiles on floor (300x300mm, 400×400 mm).
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA T4G/W PLATINUM meets the adhesion requirements of IS 15477 : 2004 “Specification for Adhesives for use with Ceramic Tiles
- Surface Preparation
The surface should be sound, clean, and free from dirt, oil or grease before MAC Platinum NSA T4G/T4W is applied. Substrate should be in Saturated Surface Dry (SSD) condition before application of adhesive. Substrates should be in plumb before application of adhesive
- Mixing
Mix 20 kg of MAC Platinum NSA T4G/T4W with 5 to 6 liters of water. Mix to a uniform lump-free consistency using a forced action mixer. Keep it for approximately 5 minutes to fatten it. Hand mixing is recommended for small quantities only. Mix as much quantity as can be consumed in 45 min.
- Application
Apply MAC Platinum NSA T4G/T4W paste on substrate with plain side of notch trowel. Press paste firmly to work into substrate.Comb with notch trowel with notched side, notch trowel to be selected as per required bed thickness. Spread as much adhesive paste as can be tiled within 15 minutes. Start placing/fixing of tiles & tap using beating block or rubber mallet. For large format tiles & stone provide back butter for 100 % coverage & firm bonding. Periodically remove a tile to check transfer of material on tile. Also check spread of adhesive, if not proper and if becomes non-sticky then scrap it & apply paste again.
- Grouting
Grouting should preferably be carried out at least 24 hours after the completion of tiling. For grout joints upto 3mm wide use Proofer High Polymer Tile Grout. For grout joints above 3mm wide use RTM Wide. After grouting clean and polish tiles with a damp sponge or cloth.
- Cleaning
Clean the tools & equipments with potable water immediately after use.
- Always add powder to liquid and not liquid to powder.
- While working in temperature more than 35OC ( 95OF ) always dampen the substrate & finish faster.
- Tiling should not be done when surface temperature is below 4OC.
Diamond NSA T5G/T5W
Engineering is concerned with the development, improvement, and implementation of inte grated systems of people, money, knowledge, information, equipment, energy, materials, analysis and synthesis, as well as the mathematical, physical and social sciences together with the principles and methods of engineering design to specify, predict, and evaluate the results to be obtained from such systems or processes.
- Quality Construction Solutions For Industries!
- Expertise & Innovation from a truly global company
- Highly Professional Staff, Accurate Testing Processes
About Diamond NSA T5G
- Our ceramic Tile Adhesive are compatible with a wide range of substrates:
- Applying ceramic wall tiles on wall internally
- Applying vitrified tiles on floor (600×600 mm, 600×1200 mm, 800×800 mm, 800×1200 mm)
- Applying floor tiles on floor (300x300mm, 400×400 mm).
- Suitable for fixing ceramic tiles for floor & wall.
- Polymer modified adhesive
- Good strength & interior situations
- Easy mixing & application
- NSA SILVER meets the adhesion requirements of IS 15477 : 2004 “Specification for Adhesives for use with Ceramic Tiles
- Surface Preparation
The surface should be sound, clean, and free from dirt, oil or grease before MAC Diamond NSA T5G/T5W is applied. Substrate should be in Saturated Surface Dry (SSD) condition before application of adhesive. Substrates should be in plumb before application of adhesive
- Mixing
Mix 20 kg of MAC Diamond NSA T5G/T5W with 5 to 6 liters of water. Mix to a uniform lump-free consistency using a forced action mixer. Keep it for approximately 5 minutes to fatten it. Hand mixing is recommended for small quantities only. Mix as much quantity as can be consumed in 45 min.
- Application
Apply MAC Diamond NSA T5G/T5W paste on substrate with plain side of notch trowel. Press paste firmly to work into substrate.Comb with notch trowel with notched side, notch trowel to be selected as per required bed thickness. Spread as much adhesive paste as can be tiled within 15 minutes. Start placing/fixing of tiles & tap using beating block or rubber mallet. For large format tiles & stone provide back butter for 100 % coverage & firm bonding. Periodically remove a tile to check transfer of material on tile. Also check spread of adhesive, if not proper and if becomes non-sticky then scrap it & apply paste again.
- Grouting
Grouting should preferably be carried out at least 24 hours after the completion of tiling. For grout joints upto 3mm wide use Proofer High Polymer Tile Grout. For grout joints above 3mm wide use RTM Wide. After grouting clean and polish tiles with a damp sponge or cloth.
- Cleaning
Clean the tools & equipments with potable water immediately after use.
- Always add powder to liquid and not liquid to powder.
- While working in temperature more than 35OC ( 95OF ) always dampen the substrate & finish faster.
- Tiling should not be done when surface temperature is below 4OC.
